- Description
- Specifications
- Have a Question About This Item
- Shipping Policy
- Exchange, Returns, and Refunds Policy
How to tension spring
How to change battery
What you receive?
-
1x Set of buttons
-
1x Remote case/Blank key
Please Note: This product does not include logos and is an aftermarket product.
What is not included?
- 1x Remote Electronics (internals)
This listing is intended for when your key has external damage but the internal remote chip still works. Transfer your remote chip to our product and you will have a brand new working remote.
Is this compatible with my car/key?
Yes, if your car is one of the following below and your current key/remote looks identical to the product pictured in the main image:
Holden Car Key Models
-
Barina (TM) 2011 – 2014
-
Cruze (JG) 2009 – 2010
-
Cruze (JH) 2010 – 2014
-
Trax 2013 – 2014
Chevrolet Car Key Models
- Camaro 2010 – 2013
- Cruze 2011 – 2013
- Equinox 2010 – 2013
- Malibu 2013
- Spark 2013
- Sonic 2012-2012
- Volt 2011-2013
Instructions:
Replacing the case on your Holden remote is a straightforward task that can be accomplished by anyone.
- A pair of Circlip (reverse) pliers
- A small fine point flathead screwdriver
- A small Phillips head screwdriver
- If your original shell has a logo on the back using the fine point flathead screwdriver gently lever the logo up. Once the logo is lifted there will be a small Phillips head screw exposed, remove the screw. If your key doesn't have a logo on the back proceed to step 2.
- With the blade still unfolded there will be a small opening right behind the blade mounting. Insert the circlip pliers & pry apart the case
- Extract the internal circuit board. Please verify that the transponder is present on the circuit board. This is a small, rectangular chip located on the top end of the circuit board. If it is absent check the upper right of the old case. It may need to be transferred.
- Place the circuit board & transponder into the new key case in the correct positions. There are always little tabs or clips to put them into to make sure they are 100% aligned with the buttons when complete.
- Securely snap & fasten the new case & install the screw in the back. Then conduct a test to ensure that everything functions properly.
- Use a 0.8mm pin punch to extract the roll pin from both new & old key blade mounts. Remember to retain the pins from each.
- Note that the pin is inserted into a groove on the blade, which is slightly misaligned in the old blade compared to the new one.
- Use a needle file to carefully elongate the groove in the correct direction, checking the alignment with the old blade in the new mount until you can see through the pinhole.
- Once the groove is correctly elongated, use the original blade in the new mount and reinstall the roll pin. Finally, reassemble the key.
Case Dimensions: 6.4cm x 3.5cm x 1.8cm
Blade Type: HU100
Details:
- This is NOT a complete key and does NOT include electronics or transponder chips
- Our keys are not included with logos
- Cutting of the key must be performed by an automotive locksmith
- Generally, a key housing will be suitable if the exterior, internal structure and blade type are identical. If unsure please send us detailed images of your current key
- When transferring the electronics, please ensure the transponder chip is also transferred. Do not discard any part of the original key until you have confirmation the new key is working (buttons work and car starts)
Warranty and Returns:
We accept 30 day returns and offer 12 month warranty on all items. If the key blade has been cut, we are unable to accept a return. Return postage is at the buyer's expense and a restocking fee may apply.
Disclaimer:
We distribute automotive keys, remotes and casings which are compatible with the vehicles produced by other manufacturers, and which are substitutes for automotive keys, remotes and casings produced by those manufacturers. Except where a product is expressly stated to be a "genuine" product. Our products are not produced by, and are not authorised, endorsed or approved by these other manufacturers.
Battery Type:
Battery type TBA
Battery Access Type:
Tool Required
AS62368.1 Compliant:
Compliance TBA
Battery Included:
No
Contains Coin Battery:
Coin Battery TBA
Products are delivered Australia wide using Australia Post (Registered Post). Shipping costs are influenced by the size and weight of the product and your location, exact shipping costs are calculated in the shopping cart and will be added to the order total before checkout.
Orders are dispatched within 2 business days and shipping times are estimated at between 3-10 business days depending on your location within Australia. Please be aware deliveries outside of metropolitan areas may take longer. This service will require your signature when the parcel is delivered. If you are not available at time of delivery, a card will be left for you to collect your parcel from the nearest Post Office.
View Store PoliciesPlease choose carefully before you buy.
For faulty products, Remote Pro offer a 14 DAY REPLACEMENT WARRANTY, from the date you receive your product. They do not offer a satisfaction guarantee on any of their products, however due to their high level of customer service, they will always endeavour to keep customers happy and satisfied.
If your product is faulty, it will be replaced with an identical product. If they cannot replace the product, they will offer you the option of choosing another product of the same value, or provide you with a refund for the total value of the faulty product.
Please note: Standard postage fees apply to all return orders. Where the return relates to a faulty item, the replacement product will be sent out to you, at no charge, within 5 working days from the date we receive the faulty product.
When returning your product, please make sure you provide the following details:
- Your full name
- Your order number
- Reason why you are returning the product
- Your instructions informing us how you would like the issue resolved.
Please include the original order confirmation or invoice you received with your product. Also, if you haven't previously provided a contact phone number, please include this with your return. This will ensure the issue is resolved quickly, should anyone need to contact you.